oscam.server(5)

NAME
oscam.server - reader configuration file for OSCam

SYNOPSIS
The server configuration file for OSCam contains reader parameters. sections in oscam.server are recurring (more than one reader possible). At least one [reader] section is required.

DESCRIPTIONS

  The [reader] section

label = name
    name for reader, required

enable = 0|1
    0 = deactivate reader, default:1

description = text
    description of reader, default:none

protocol = reader protocol
    reader protocol, required:
     camd35|cs357x
     cccam
     cs378x
     constcw
     gbox
     ghttp
     internal
     mouse
     mp35
     newcamd|newcamd525
     newcamd524
     pcsc
     radegast
     scam
     sc8in1
     serial
     smargo
     smartreader

device = [<readertype>;]serial:serialnum|bus:device|
         <device|device:slot>|
         <ip|hostname>,<port>[,<lport>]|
         <ip|hostname>,<gboxpport>|
         <ip|hostname>,<scamport>|
         pcsc|
         <0|1>>|
         constantcw
    define local or remote reader
     readertype: set reader type
                    SR: Smartreader+ (default)
                    Infinity: Infinity USB
                    TripleP1: Smargo Triple Reader port 1
                    TripleP2: Smargo Triple Reader port 2
                    TripleP3: Smargo Triple Reader port 3
     bus:device: bus name and device name of the Smartreader+ or
                  Infinity USB (get the names with lsusb 'Bus'
                  and 'Device')
     serialnum: serial number of reader of the Smartreader+ or
                  Infinity USB
     device: device name
     device:slot: device name and slot number sc8in1 [1-8]
                  (only one SC8in1 reader supported)
     ip|hostname: IP address or host name
     port: TCP/IP port
     lport: remapping to local TCP/IP port
     gboxpport: UDP port for remote gbox peer
     PCSC: number of PCSC reader, starting with 0
     0|1: for Coolstream HD-1 STB only: select reader 0 or
                  reader 1
     constantcw: constant CW file name constant CW file format:

    • standard format
        CAID:Provider ID:Service ID:PMT ID:ECM PID::key (16 Bytes seperated by spaces) example: 1234:123456:1234:2345:3456::00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

    • extended OScam format
        CAID:Provider ID:Service ID:PMT ID:ECM PID:Video PID:key (16 Bytes seperated by spaces) example: 1234:123456:1234:2345:3456:7890:00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

detect = [!]CD|[!]DSR|[!]CTS|[!]RING|[!]NONE|[!]gpio[1-7]
    status detect of card, NONE = no detection, ! = inverse, default:CD

cardmhz = mhz
    set standard SC frequency in units of 10 kHz, for Irdeto SC set to 600 mhz, for Dreambox DM800 / DM8000 set to 2700 mhz, for Dreambox DM7025 set to 8300 mhz, for older PowerPC Dreambox STBs set to 3150 mhz, refer to OVERCLOCKING, default:357

mhz = frequency
    set reader frequency in units of 10 kHz, if mhz > cardmhz you are in overclocking mode. For Smargo readers and Dreambox internal readers frequency will be set by ATR if autospeed is set to 1, default:357

autospeed = 0|1
    1 = sets mhz according to ATR. Currently only used for smartreader, Smargo and Dreambox internal protocol, other readers will be adapted to use this parameter as well. If You wan't to overclock you're card set it to 0, default:1

deprecated = 0|1
    First the SC will be initialized in normal mode. If it fails, the SC will be automatically reverted to deprecated mode, so that the SC speed will not be changed and the communication will remain on normal ATR speed of 9600 baud. 1 = use deprecated SC mode only, default:0

mode = mode
    set card init mode for AzBox internal reader, default:none

smargopatch = 0|1
    1 = enable workaround for Smartreader+ reader until native mode works, default:0

sc8in1_dtrrts_patch = 0|1
    1 = enable fix for SC8in1/MCR DTR/RTS kernel bug, default:0

use_gpio = 0|1
    1 = use GPIO to init the reader. This needs to be set on WRT54G router, default:0

ins2e06 = payload
    add check control for pin payload (4 hex bytes) for NDS Videoguard 2 SCs, valid for physical readers only, default:none

ins7e = payload
    add 26 hex-bytes payload for NDS Videoguard 2 SCs, valid for physical readers only, default:none

ins7e11 = TA1 byte
    set TA1 byte for NDS Videoguard 2 SCs, valid for physical readers only, default:none

fix07 = 0|1
    1=enable 0x07 fix for NDS Videoguard 2 SCs, valid for physical readers only, default:1

force_irdeto = 0|1
    1 = force Irdeto SC mode even if RSA key is set for Irdeto tunnled Nagravion SC, default:0

nagra_read = 0|1|2
    read Nagravison records (on NCMED SCs only):
     0 = disabled (default)
     1 = read all records with expired rights
     2 = read records with valid rights only

rsakey = RSA key
    RSA key for Nagravision/Tiger SCs, CAM key data for Irdeto SCs, Conax SCs, default:none

deskey = DES key
    DES key for Viaccess SCs post-processing, default:none

boxkey = box key
    box key for Nagravision SCs / CAM key for Irdeto SCs

pincode = pincode
    pincode for Conax, Cryptoworks and Viaccess SCs, default:none

fix9993 = 0|1
    1 = enable fix for 9993 error with CAID 0919 Videoguard SCs, default:0

readtiers = 0|1|2
    method to get tiers of NDS Videoguard SCs:
     0 = disabled (default)
     1 = ins70 method
     2 = ins76 method

boxid = NDS box ID
    NDS receiver box id

ndsversion = 0|1|12|2
    set NDS Videoguard version
      0 = autodetection (default)
      1 = NDS Videoguard 1
     12 = NDS Videoguard 1+
      2 = NDS Videoguard 2

aeskeys = CAID #0@provid:AES key #0 CAID #0[,AES key #1 CAID #0],...[;CAID #1@provid:AES key #0 CAID #1[,AES key #1 CAID #1],...]...
    multiple 16 bytes AES keys for Viaccess SCs (the used postprocessing AES key is specified through the D2 nano of the ECM) special AES keys:
     00 = do not return any CW, no AES key specified
     FF = return CW received from the S, no AES key specified example:
     aeskeys = 0500@012345:000102030405060708090a0b0c0d0e0f;0500@543210:000102030405060708090a0b0c0d0e0f,0,0f0e0d0c0b0a090807060504030201

key = DES key
    key for newcamd remote reader encryption

user = name
    user for remote reader

password = password
    password for remote reader

services = [!]services[,[!]<services>]...
    reader [de]assignment to service group, default=none

caid = <CAID>[&<mask>][:<target CAID>][,<CAID>[&<mask>][:target <CAID>]]...
    define and mapping of CAIDs for reader, default:all CAIDs with mask FFFF example: caid = 0100
             caid = 0200&ffee:0300
             caid = 0400&ff00:0500,0600
             caid = 0702,0722
             caid = 0702&ffdf (shortcut for the example above)

ident = <CAID>:<provid>[,provid]...[;<CAID>:<provid>[,provid]...]...
    set CAID and SC specific ident for reader example: ident = 0100:123456,234567;0200:345678,456789

class = [!]class[,[!]class]...
    set SC specific class in hex for reader example: class = 01,02,!1b,!2b

chid = CAID:ChID
    set SC specific ChIDs for reader, default:none example: chid = 0100:12

group = 1..64[,1..64]...
    reader assingment to groups, default:none, required

audisabled = 0|1
    1 = exclude reader from auto AU, default:0

auprovid = provider ID
    set provider ID to use the right reader for auto AU example: auprovid = 123456

disableserverfilter = 0|1
    1 = ignore caid and provid settings of reader due faulty clients, default:0

inactivitytimeout = seconds
    inactivity timeout for all TCP based remote readers, -1 = reconnect on network failure for newcamd, even in idle, default:0

reconnecttimeout = seconds
    reconnect if missing answers from a remote reader, default:30

reconnectdelay = milli-seconds
    set maximum TCP connection block delay, default:60000

connectoninit = 0|1
    1 = allow newcamd connections to be established on startup although there isn't a request yet, default:0

keepalive = 0|1
    1 = allow cs378x TCP socket to be always connected, default:0. Always on if cacheex reader type.

fallback = 0|1
    1 = define reader as fallback, standard and fallback reader must have the same group, default:0

fallback_percaid = <CAID>[:<ident>[,ident]]...[;<CAID>[:<ident>[,ident]]...]....
    use reader as fallback for defined CAIDs only, two-digit wildcard CAIDs are possible, fallback_percaid overrules fallback, default:none
     example: fallback_percaid = 1234:234567;89;10:345678

emmcache = usecache,rewrite,logging
    set EMM cache of local reader:
     usecache = 0|1||2
                0 = EMM caching disabeld (default)
                1 = enable EMM caching and save EMMs to file after
                    stopping OSCam
                2 = enable EMM caching, don't save EMMs to file
                    after stopping OSCam
     rewrite = determines how often one and the same EMM is
                written, default:0
     logging = EMM logging mask:
                 0 = EMM logging disabled (default)
                 1 = logging EMM errors
                 2 = logging written EMMs
                 4 = logging skipped EMMs
                 8 = logging blocked EMMs
                16 = logging disabled AU
     example: emmcache = 1,3,2

cacheex = 0|1|2|3
    set cache exchange mode
     0: disable cache exchange mode (default)
     1: enable cache exchange pull mode
     2: enable cache exchange push mode for camd 3.5x / 3.57x and CCcam
        protocol
     3: enable reverse cache exchange push mode for camd 3.5x / 3.57x
        and CCcam protocol Identical cache exchange modes must be set on local OSCam server and remote OSCam user asccount. Please consider memory consumption.

cacheex_maxhop = hops
    define maximum hops for cache exchange, default=10

csp_ecm_filter = [caid][&mask][@provid][$servid],n
    cache exchange incoming ECM filter setting (mode 2 only) for Cardservproxy, default:none

cacheex_drop_csp = 0|1
    1 = drop incoming Cardservproxy cache (mode 2 only), detection is zero ecmd5, default:0

cacheex_allow_request = 0|1
    1 = allow incoming ECM request (mode 2), default:1

cacheex_allow_filter = 0|1
    1 = allow cache exchange filter (for cache exchange mode 2 only), default:1

cacheex_block_fakecws = 0|1
    1 = enable fake DCWs blocking (for cache exchange mode 2 only), get fake DCWs form oscam.fakecws, default:0

ecmwhitelist = [CAID[@provid]:]length[,length]...[;[CAID[@provid]:]length[,length]...]...
    set valid ECM length per CAID and provid in hex, default:none,provid=000000 example: ecmwhitelist = 10,20,0a,0b
             ecmwhitelist = 0100:10,20;0200@123456:0a,4b In normal operation mode this parameter is not required.

ecmheaderwhitelist = [CAID[@provid]:]header[,header]...[;[CAID[@provid]:]header[,header]...]...
    set vaild ECM header per CAID and provid in hex, default:none,provid=000000

ratelimitecm = count
    number of different SIDs in ECMs allowed for an interval, default:0

ecmnotfoundlimit = count
    number of ECMs with "not found" answer until the reader will be restarted, 0 = no limit, default:0

resetcycle = count
    number of ECMs until SC reset is performed, 0 = disabled, valid for physical readers only, default:0

ratelimitseconds = seconds
    interval for rate limit, default:0

ecmunique = 0|1
    1 = enable check for matching ECM hash in ratelimit slot , default:0

srvidholdseconds = seconds
    time to keep service ID in ratelimit slot, during this time checkeding for ecmunique is disbaled, default:0

cooldown = delay,duration
     define cooldown:
     delay: delay in seconds for which the reader is allowed to do
               more ECM requests than defined by ecmratelimit,
               default: none
     duration: duration in seconds the reader needs to cooldown,
               default:none ratelimitecm and ratelimitseconds are required

blocknano = nano[,nano]...|all
    list of EMM-nanos to block (in hex w/o 0x) or all EMM-nanos, valid for physical readers only, default:none
     example: blocknano = 45,93,7a,ff
              blocknano = all

blockemm-u = 0|1
    1 = block unique EMMs, default:0

blockemm-s = 0|1
    1 = block shared EMMs, default:0

blockemm-g = 0|1
    1 = block global EMMs, default:0

blockemm-unknown = 0|1
    1 = block unknown types of EMMs, default:0

blockemm-bylen = [length range,length range]...
    block all types of EMMs by length, default:none
     example: blockemm-bylen = 1-10,11-

read_old_classes = 0|1 (Viaccess SCs only)
    0 = read only active entitlements 1 = read all entitlements (default)

saveemm-u = 0|1
    1 = save unique EMMs to log file, default:0

saveemm-s = 0|1
    1 = save shared EMMs to log file, default:0

saveemm-g = 0|1
    1= save global EMMs to log file, default:0

saveemm-unknown = 0|1
    1 = save unknown types of EMMs to log file, default:0

savenano = nano[,nano]....|all (obsolete)
    list of EMM-nanos to save (in hex w/o 0x) or all EMM-nanos, only valid for physical readers, default:none
     example: savenano = 45,93,7a,ff
              savenano = all

readnano = [path]filename
    write file (usually a copy of a file saved by savenano) to your smartcard, if no path is specified, the specified file is searched for in the configuration directory, only valid for physical readers, default:none
     example: readnano = write.emm
              readnano = /var/oscam/write.emm

dropbadcws = 0|1
    1 = reject bad CWs, send "not found" instead of bad CWs, default:0

disablecrccws = 0|1
    1 = disable CRC for CW, default: 0 In normal operation mode this parameter is not required. Parameter is incompatible with DVB standard.

ident = <CAID1>[:<ident1>[,<ident2>]...][;<CAID2>[:<ident3>[,<ident4>]...]]...
    use this reader as local in loadbalancer's reader selection, default:none

lb_whitelist_services = <services>,<services>...
    reader assignement to service group for channels which may never be blocked by the loadbalancer to the reader , default=none

lb_weight = weight
    the higher the value the higher the probability for reader selection in load balacing mode, default:100
     It's an divider for the average responstime.

lb_force_fallback = 0|1
    1 = set the reader always as fallaback for load balacing without considering the reader's statistics, default:0

cccversion = <main version>.<version>.<sub version>
    set CCcam version, default:none example: cccversion = 1.2.34

cccmaxhops = hops
    set CCcam maximum SC distance hops, default:10
     -1 = disabled
      0 = remote local SCs only
      1 = remote local SCs and + 1 hop
      2 = remote local SCs and + 2 hops
     and so on After reading this SC hop will be incremented by one.

ccchop = hop
    set hop for non CCCam readers, default:0

cccreshare = hop
    set reader's CCcam reshare hop, default:0
     -1 = reshare value off cccam in global config
      0 = resharing for direct peer only
      x = resharing for direct peer and share level x

ccckeepalive = 0|1
    1 = send keepalive messages to keep connection to remote CCCam server up, default:0

cccreconnect = timeout
    reconnect again after ECM request timeout in milli-seconds, default:4000

cccmindown = number
    filters all readers with hops smaller than number, default:0

gbox_reshare = level
    gbox reshare level of local cards, default:0

gbox_max_distance = distance
    maximum distance to receive gbox peer cards, default:2

gbox_max_ecm_send = number
    maximum of gbox peers ECMs will be send to, default:3

use_ssl = 0|1
    1 = use SSL for ghttp protocol, default:0

OVERCLOCKING

•   Dreambox and other internal readers For Dreambox and other internal readers the highest possible clockrate will be auto detected. The mhz parameter lets you override the values chosen by OSCam, if it differs from 357 and 358, but usually you will not set any value for mhz. For certain Dreamboxes (especially PPC clones) the default mhz parameter leads to slow ECM times and/or "not found" ECMs. By setting mhz to values like 200, 300, 400, ... 1600 you can find a value that works for your receiver and your card. The higher the mhz value, the slower the ECM time (strange enough). If you choose the value too low, your card is not recognized (no ATR or "card not supported"). If you choose the value too high, you get slow ECM times. Our experience is that either no mhz line, or a line mhz = 1000 works best.

•   Phoenix / Smartmouse reader Overclocking does not work with Windows and Mac OS X. Set mhz equivalent to the frequency of the reader. OSCam can not set the frequency of the reader.

•   Smargo Smartreader+ Use protocol = smargo for the FDDI kernel drivers (no libusb needed) or (not recommended) use protocol = smartreader for OSCam's driver implementation based on libusb. Set the reader frequency with the native Smargo Smartreader+ tool (srp_tools). If not setting mhz and cardmhz, OSCam tries to set the baudrate automatically, according to the maximum speed indicated by ATR. Overclocking is possible.

OSCam tries to set the baudrate automatically. A standard serial port has limited baudrate settings, so SC overclocking might not work. When using a serial reader the best way for overclocking is connecting it to a FTDI based USB to serial port adapter. If overclocking does not work, verify the effective baudrate in the logfile. If it deviates too much from the requested baudrate, the SC will not be recognized (no ATR) and the value for mhz should be adjusted again. The higher the baudrate, the more accurate the effective baudrate can be.

CACHE EXCHANGE

•   pull mode (on request: cache exchange from remote to local OSCam) ECM requests will be forwarded to the remote cache exchange partner. If the CW could not be found in the cache of the remote exchange partner, a not found will be answered. If the CW could not be found in the cache of the remote exchange partner but a pending ECM request is open, the request will be re-initiated after the wait time defined in cacheexwaittime.

•   push mode (continuous: cache exchange from remote to local OSCam) CWs from the remote cache exchange partner will be forwarded to the local cache. Forwarding only works while the camd camd 3.5x / 3.57x or CCcam protocol connection between the local and remote OSCam has been established.

•   reverse push mode (continuous: cache exchange from local to remote OSCam) CWs from the local cache will be forwarded to the remote cache exchange partner. Forwarding only works while the camd camd 3.5x / 3.57x or CCcam protocol connection between the remote and local OSCam has been established.

EXAMPLES

•   serial mouse compatible reader
     [reader]
     label = myserialmousereader
     detect = cd
     protocol = mouse
     device = /dev/ttyS1
     group = 1
     caid = 0100
     services = myservice,!thisservice

•   USB mouse compatible reader
     [reader]
     label = myusbmousereader
     detect = cd
     protocol = mouse
     device = /dev/ttyUSB0
     aeskey = 0102030405060708090a0b0c0d0e0f10
     group = 2
     caid = 0200

•   camd 3.78x reader
     [reader]
     label = mycamd378xreader
     protocol = cs378x
     device = 192.168.0.1,1234
     user = user1
     password = password1
     group = 3

•   newcamd reader
     [reader]
     label = mynewcamdreader
     protocol = newcamd
     key = 0102030405060708091011121314
     device = 192.168.0.2,2345
     user = user2
     password = password2
     group = 4

•   CCcam reader
     [reader]
     label = mycccamreader
     protocol = cccam
     device = 192.168.0.3,3456
     user = user3
     password = password3
     group = 5
     caid = 0300,0400,0500
     cccversion = 1.2.3

•   PCSC reader
     [reader]
     label = mypcscreader
     protocol = pcsc
     device = 0
     aeskey = 0102030405060708090a0b0c0d0e0f10
     group = 6
     caid = 0600

•   Smargo Smartreader+
     [reader]
     label = mysmartreader
     protocol = smartreader
     device = 001:002
     aeskey = 0102030405060708090a0b0c0d0e0f10
     group = 7
     caid = 0700

•   internal reader
     [reader]
     label = myinternalreader
     protocol = internal
     device = /dev/sci0
     group = 8
     caid = 0800

•   sc8in1 reader
     [reader]
     label = mysc8in1reader
     protocol = sc8in1
     device = /dev/ttyUSB0:1
     group = 9
     caid = 0900

•   constant CW
     [reader]
     label = myconstantcw
     protocol = constcw
     device = /var/keys/constant.cw
     group = 10

•   gbox reader
     [reader]
     label = mygboxreader
     protocol = gbox
     device = 192.168.0.4,45678,56789
     user = user4
     password = password4
     group = 11
     caid = 1100

SEE ALSO
list_smargo(1), oscam(1), oscam.ac(5), oscam.cacheex(5), oscam.cert(5), oscam.conf(5), oscam.dvbapi(5), oscam.fakecws(5), oscam.guess(5), oscam.ird(5), oscam.provid(5), oscam.ratelimit(5), oscam.services(5), oscam.srvid(5), oscam.srvid2(5), oscam.tiers(5), oscam.user(5), oscam.whitelist(5)